RetroVenue.com

I’m addicted. I didn’t think it would happen but now it’s too late. As a polymer clay addict, I thought this was too temperamental and time consuming to become another addiction. I was wrong. Wrong twice: I never thought metal could have these colors. More photos

Today's Favorite

This time I kept the temperature closer to 1550F for two hours. I forgot to raise the container up so the air and heat can circulate but it didn’t seem to matter.

There seems to be no pattern to the resulting colors. I had some that were fired before, some that dried for over 48 hours, and some that dried for about 12 hours. Last time they were in the fridge to dry, not this time. I did notice a little warping that had to be corrected this time.

Not So Identical Twins

The 2 circles had been fired and buffed. Except I did not remove a beautiful red “splotch” on one of them. Is that the one that has so much red after being fired today? The other one has a lovely gold center and more orange outer ring. But they sure don’t look like they belong together. Next time I will refire the green ones and see if they become more colorful with greens.

I suspect there is no pattern. What if it is totally random based on temperature? The difference in matching pieces fired quite near one another might also be a result of one staying in the charcoal longer than the other. What if instead of fishing them out with a slotted spoon, the charcoal could be poured through some sort of screen?

Well, there will be a next time. Maybe the mystery will be solved then.

I bought Bronze Clay some time ago.  After reading a basket full of experiences online and conflicting instructions, I never got around to opening the packages.  This weekend I got brave and set aside plenty of time to work with it.  

My first attempt to condition the clay was a mess even though it was on a well oiled plastic (former) page cover.  I pressed on.  The glob went in the fridge to cool while the moisture content evened out.  It was time to clean up my hands! And my work area. Then I got out the other tools. (If you’d rather skip the rest you can check out the photos.)

Formed Bronze Clay

To my surprise about a half hour later, the glob came out of the fridge without an attitude.  Now I could work with it. This was not so bad after all.  The texture and consistency was pretty good. 

I decided to do a variety of shapes, all about 3mm (7 cards) thick.  The concoction in the middle is “mud” to fill any cracks before firing. Somewhere I read that using a magnifying glass would be a better way to spot those cracks that tend to show up after drying and greatly expand during firing.  I got out my magnifying glass that is used mostly for reading pottery markings.  That would come in handy later.

I added a couple bronze jump rings and a copper wire  to 3 pieces to test the results.  Who wants holes shrinking leaving no way to connect magnificent new pieces? All the pieces sat out at room temperature to dry over night. No warping was noticed. A few small cracks were filled.  Bumps were smoothed.  After checking (one more time) a series of charts and instructions for bronze clay in a Paragon Firefly kiln, I was ready to start.  I decided to go with the fast ramp up, and to try to keep the temperature at 1490 F for 2 hours.  A bit of a chore because my kiln is not programmable. But not nearly as big a chore as trying to control the ramp up time.

I thought two hours left me plenty of time to do a few other things.  Then the temperature starting going up, reaching 1550F and even a few degrees more before I convinced it to return to the 1490F range.  

Burnished and Refired with glass

My kiln is outside on an enclosed stand that has a cover.  Despite the threat of rain, probably a bad idea to lower the cover. The temperature stabilized, with the readings fluctuating between 1488F and 1508F. No more incidents. The 2 hours passed. I unplugged the kiln.  When it reached about 500F, out came the stainless steel container. Fishing around in the carbon particles with the required slotted spoon didn’t take too long to find all the pieces. But I can see why it would be important to keep in mind how many pieces you were firing.

Here are 2 of the pieces after being burnished.  They went back in the kiln to see if I can get glass frit to stick to them.  That’s a story for another day.  More photos